That could be created in the complex, which comprises many installations connected by bridges. The 1985 event attracted 312 participants, who received medals from a popular sports association.
The Ekofisk March proper began the following year. Schulstock and others had made detailed preparations and ordered their own diplomas, badges and medals for everyone who completed the course. This has since become an annual event which calls for a good deal of administration on a voluntary basis, with the motif on medal and badge varying from year to year.
During the first three years, it was taken from the Ekofisk Complex. Since then, it has varied between the other installations on the field. The year is also stated. Bronze, silver and gold medals were awarded for the first three years, replaced by a bronze series involving all the outer platforms. Silver and gold series followed.
Hot dog and juice stations
A positive social framework is important on the marches. Once people start walking, the smiles emerge. Hot dogs and juice are provided at stations around the course. If blisters become too irksome, first aid is available. The march is a little special since everyone must wear a hard hat – but people are allowed to replace protective footwear with other suitable shoes.
The march takes place around 18.30. Several sessions mean everyone has a chance to take part, but completing the whole series may take a couple of months.
The march is staged on all the installations, and how many circuits need to be completed on each platform has been carefully calculated.
March as prize
The Ekofisk mountain walking club is a member of Norway’s mountain walking association, but one requirement for taking part is a job in the Greater Ekofisk Area. However, some exceptions are allowed. Participation was a special prize announced by the association one year for members who deserved special recognition for taking a mountain walk despite a handicap.
The winner, Johannes Bratrud, was blind. He and his wife Karin were flown out to Ekofisk, and his white stick was an unusual sight in an offshore workplace where everyone needs a valid medical certificate. But nobody could spot that he was unable to see when doing the Ekofisk March accompanied by Karen, his wife. The same applied in the evening when a social event with orchestra was staged. He and Karin danced as well as anyone else.
Later, a draw was held for several years for participants in the annual Phillips March in Tananger, with the winners getting an unforgettable trip offshore to do the Ekofisk March.
Income for good causes
T-shirts have been produced with an Ekofisk March motif for sale, with the profits given to good causes. On the 10th anniversary in 1995, NOK 80 000 was donated after a careful assessment to the Salvation Army. Phillips was generous enough to double that amount. Former cross-country skiing champion Oddvar Brå was also specially invited to participate in the march on its 10th anniversary.
Peak turnout in some years has been 2 390. Participation has later stabilised at an annual average of about 550.
Other Norwegian offshore installations, including ones on the Oseberg and Statfjord fields, have later followed up with similar arrangements.
All the supplies needed to ensure that the offshore platforms can do their job of producing oil and gas pass through the base at Tananger outside Stavanger. Warehouse operation at the base covers five main functions: goods reception, spare parts store, accounting, pipe store and goods dispatch.
— Phillips is about to establish themselfs at the Norsco base,1972 Photo: Norsk fly og flyfoto/Norwegian Petroleum Museum
The contract for Phillips’ first supply base in Norway was signed with Stavanger-based tanker company Smedvig Tankrederi on 25 April 1966.
It covered the hire of outdoor storage and quay areas as well as a new combined warehouse and office building which was modest by today’s standards.
Located at Dusavik just outside Stavanger, Phillips ranked as the first tenant at what was to become one of the two big offshore supply bases in the district.
The drilling operations which led to the discovery of Ekofisk were served from Dusavik. While the lease ran until 1981, it only functioned as the main base for the Stavanger area until 1973.
Rapid organisational growth made the premises in Dusavik too small by that year, and additional space was obtained by taking a clearly creative approach.
So Phillips secured premises in a soap factory, a Chinese restaurant and the bar and other areas of Stavanger’s Alstor Hotel. And many of those hired in 1973 are sure to remember that they were interviewed at the city’s Atlantic Hotel.
Phillips base, 1973-81
Some activity had been established at the Aker Norsco base in Tananger during 1972, but it was not until the autumn of 1973 that the headquarters for Ekofisk was transferred from Dusavik.
That occurred with the occupation of the H Building at Tananger, where Phillips had signed a lease with the base company the year before.
This covered the hire of outside storage areas, quays, warehousing, a canteen and an office building – a complete supply base. All the buildings were purpose-built.
The lease gave Phillips an option to acquire the whole facility at a later date, which the company duly exercised in the summer of 1979.
To varying degrees since 1973, the operator has needed to lease both warehousing and offices from Aker Norsco – partly in temporary structures and partly in permanent premises.
From 1973 to 1976, exploration operations with the Ocean Viking rig continued to be run from the Dusavik base. The charter then expired, and remaining activities were moved to Tananger.
Lack of space at the latter premises meant that the training department was transferred to Dusavik and remained there until the lease expired in 1981.
Similar shortages meant extra premises had to be leased around Stavanger. This growing problem led to plans being laid from 1978 for a significant expansion at Tananger.
Phillips base since 1981
The new building was gradually occupied from December 1980 and formally opened in August 1981. Once it had been finished, the old H Building was completely refurbished to the same standard.
This expansion marked a significant improvement in working conditions for many employees, and helped to enhance efficiency by gathering much of the organisation under one roof.
The development was originally intended to meet all needs for office space, with the exception of the project department’s requirements.
However, it became clear even before the new building was occupied that this goal would not be reached. But it proved possible by and large to cease hiring space outside Tananger.
To deal with developments in the supply services for Ekofisk, Phillips entered into a contract with Aker Norsco on the construction of a larger and more modern warehouse.
This building and associated offices were occupied in late 1982/early 1983, and were regarded as a model example for the purpose.
The waterflooding project on Ekofisk received a green light in 1983, which created the need for more office space to accommodate the project department.
Since a quick start was important, the new building in Tananger was ready three months after the contract with Aker Norsco had been signed.
Premises utilised by Phillips in the Stavanger area by 1988 comprised 20 000 square metres of offices, 10 000 square metres of storage space and 850 square metres of workshops. In addition came the offices at Munkedamsveien in Oslo.
Another new building opened at the Tananger base in July 1996, which meant the whole workforce was assembled on one site in two connected premises.
While the old offices covered 14 000 square metres, the new seven-storey building has an area of 11 300 square metres and provides 420 additional office spaces.
It also accommodates a 600-square-metre conference centre, as well as a gym and a swimming pool measuring eight by 12.5 metres in the basement.
The Tananger base was sold in July 1996 to Aker Base, including buildings, furniture and fittings, and the deepwater quay.
Activities at the base
The Phillips base at Tanager plays a central role in operating the Greater Ekofisk platforms. All necessary supplies allowing these installations to do their job pass through it.
Warehouse operation at the base covers five main functions: goods reception, spare parts store, accounting, pipe store and goods dispatch.
The spare parts store is managed with the aid of a comprehensive computer system with full information for offshore personnel to log on directly and check availability.
When goods are received at the warehouse, they are marked with a purchase number and all data concerning the order is entered. They are packed out, checked and sent for shipment offshore.
The workshop, located in the same building as goods reception, deals with such jobs as mechanical repair of diesel engines, pumps, valves, heat exchangers and compressors.
It also repairs base equipment, like forklift trucks, cranes and fire-extinguishing systems. In addition, the shop produces pipework, pressure tanks and other structural welding.
The head office for Phillips’ activities in Norway stands alongside the supply base for the platforms in the Greater Ekofisk Area.
Published 29. July 2019 • Updated 22. October 2019
Oil and gas from the Greater Ekofisk Area is piped to Teesside in the UK and Emden in Germany respectively, where the pipeline terminals formed part of the field development. ConocoPhillips still operates the oil terminal in Teesside, while the facility in Emden has been taken over by Norwegian state-owned company Gassco.
— Gassterminalen i Emden. Foto: Husmo Foto/Norsk Oljemuseum
The terminal at Teesside in north-east England receives oil and natural gas liquids (NGL) by pipeline from the Ekofisk field. It comprises stabilisation, NGL fractionation, storage tanks for crude oil and an export port.
After arriving through the Norpipe Oil line, crude and NGL are separated and the oil goes through a stabilisation process before reaching the 10 storage tanks, which each hold 750 000 barrels.
The NGLs go to the fractionation facility, with a daily capacity of 64 000 barrels, for separation into methane, ethane, propane, and normal and iso butane.
While the methane (natural gas) is used to fuel the plant, the other products (now known as liquefied petroleum gases – LPG) are made liquid by cooling and stored for export by sea.
One reason for the choice of Teesside as the landfall for the Ekofisk pipeline was the opportunity it offered to install deepwater quays.
The terminal has four of these, with those for crude oil able to handle tankers up to 150 000 deadweight tonnes. The LPG quays can accept carriers loading as much as 60 000 cubic metres.
Two of the crude oil quays lie on the main channel of the River Tees, while the others have been installed in dredged docks.
Gas terminal in Emden
Gas arriving at the Emden terminal from the Ekofisk Complex enters nine parallel treatment trains for cleaning, metering and onward distribution to the buyers.
The North Sea gas is very clean, and needs only limited treatment to remove small amounts of sulphur compounds using an absorption process. Impure molecules from the gas accumulate on the surface of small particles, which act as filter spheres.
Each of the nine trains comprises four process columns and a process oven. The gas enters the top of a column and leaves through the base after passing through the filter spheres.
That leaves the gas ready for sale, and it is piped to the fiscal metering station before entering the buyer receiving pipelines and distribution network.
Three separate commercial pipeline systems connect to the terminal, operated by Ruhrgas, BEB and Gastransport Services (previously Gasunie) respectively. They pipe the gas away on behalf of the gas buyers.
The Norsea Gas Terminal in Emden was officially opened in September 1977 by Norwegian industry minister Bjartmar Gjerde and Phillips executive Gordon Goerin.
Ranking as the first gas sales deal for the Norwegian continental shelf, the Ekofisk agreement paved the way for later contracts covering other fields off Norway.
Regularity at the Emden terminal has been very high, with its own equipment never causing shutdowns. Maintenance takes place when other parts of the system are off line.
The terminal has a daily capacity of about 2.1 million cubic feet of gas per day.
Gas transport restructured
Norpipe AS owned the gas pipeline from Ekofisk to Emden until the transport system for the Norwegian offshore sector was restructured at 1 January 2003.
Norsea Gas A/S furthermore served as the formal owner of the Emden facility, with Phillips Petroleum and then ConocoPhillips as operator for both pipeline and terminal.
Since 2007, Norway’s state-owned Gassco company has been responsible for technical operation of the facilities on behalf of their owners.
That included operator responsibility for the H7 and B11 booster platforms along the gas pipeline, which were shut down in 2007 and 2013 respectively and have since been removed.
The Gassled partnership is a project collaboration embracing 10 companies which collective own large parts of the gas infrastructure on the Norwegian continental shelf (NCS).
A substantial proportion of Norway’s gas deliveries to Germany continues to arrive at the Emden terminal, including the volumes piped from Ekofisk.
Preliminary planning for a new terminal in the German port began in 2011, with Gassled taking the investment decision for this development in the autumn of 2012.
Construction work began in the following year, with the new facility being built on an unused part of the existing terminal site.
The new terminal has not expanded export capacity. But its functionality is well adapted to future processing needs for fields in the Greater Ekofisk Area and other parts of the NCS sending gas through the Norpipe system.
It was officially opened on 24 May 2016 by Elisabeth Aspaker, the Norwegian government minister for the EU and the European Economic Area. That closed a chapter in Ekofisk’s history.
Source: ConocoPhillips Norge
Published 29. July 2019 • Updated 12. October 2019
Two export pipelines run from the Ekofisk Complex. The one for gas has an external diameter of 36 inches and extends 443 kilometres to the German coastline. With an external diameter of 34 inches, the oil pipeline runs for 354 kilometres to Teesside in north-east England.
— Gas pipes at Ekofisk. Photo: Husmo Foto/Norwegian Petroleum Museum
In addition to ConocoPhillips’ own production from Ekofisk, these pipelines carry gas and oil from the company’s fields in the UK sector and from other fields on the Norwegian and British continental shelves.
The three fields in the Greater Ekofisk Area are also tied together by pipelines.
Oil pipeline to Teesside
The pipeline linking Ekofisk with the terminal for oil and natural gas liquids (NGL) at Teesside on the north-east English coast became operational in October 1975.
Pumps raise the pressure of the oil and NGL before they start their journey to land. Two pumping stations – 37/4 A and 36/22 A – originally stood along the pipeline to maintain this pressure, but have now been disconnected and removed.
The pipeline was installed with the ability to carry a million barrels per day. However, that much capacity has never been required.
In the UK sector, a 24-inch pipeline has been tied in with a Y connection to receive input from several British fields – including the J block developments operated by ConocoPhillips.
Output from the Greater Ekofisk Area is supplemented by crude from Valhall, Hod, Ula and Gyda heading for Teesside, optimising pipeline utilisation and thereby boosting value creation.
The pipeline is owned by Norpipe Oil AS and operated by ConocoPhillips.
Gas pipeline to Emden
This pipeline became operational in September 1977. The starting pressure of around 132 bar is provided by compressors on the Ekofisk Complex.
The 443-kilometre distance to Emden was split into three equal sections, with platforms B11 and H7 located at the intermediate points to provide boosting if required.
However, additional compression was seldom needed on the final stage to Emden. H7 was shut down in 2007 and B11 in 2013, and both have since been removed.
These two booster platforms were located in the German sector of the North Sea, while the pipeline also crosses the Danish sector.
The pipeline has been trenched or covered with sand. Its final section passes the island of Juist before making landfall on the coast of East Friesland to the north of Emden.
Its daily capacity is roughly 59.4 million standard cubic metres (2.1 billion cubic feet). In addition to gas from the Greater Ekofisk Area, it carries output from Valhall, Hod, Ula, Gyda and the Statpipe system (primarily Statfjord and Gullfaks).
Source: ConocoPhillips Norge
Published 29. July 2019 • Updated 12. October 2019
The Phillips group was awarded block 2/7 as early as 1965, and the Embla reservoir lies in the southern part of this acreage. Drilling began there in 1974 to depths of 4 500-5 000 metres, but pressure and temperature in the wells were too high for testing with the available equipment.
The first production well was not drilled and tested until 1988, followed by a second in 1990. Both yielded very promising results, and the field came on stream in May 1993.
Embla comprises a sandstone reservoir at least 250 million years old. The other fields in the Greater Ekofisk Area comprise fine-grained carbonate rocks deposited about 70 million years ago.
The Embla reservoir has a temperature of 160°C compared with the 125°C normally found in the chalk formations 1 000 metres higher up, and its pressure is almost twice as high.
Fabricated by Heerema in the Netherlands, the Embla 2/7 D jacket (support structure) was installed by the M 7000 crane vessel. It stands 84 metres high and weighs 2 300 tonnes.
A 5.2-kilometre subsea umbilical from Eldfisk comprises three power cables for electricity supply and eight fibreoptic lines handling data transmission and telecommunication.
The platform has six production wells and an average daily output of roughly 7 000 barrels of oil. All processing and metering took place on Eldfisk 2/7 FTP until 2015, and has now been switched to Eldfisk 2/7 S.
A 14-inch flowline linked 2/7 D with 2/7 FTP and runs today to 2/7 S. Produced at Wick in Scotland, this line was floated out to the field in one piece.
Topside equipment includes the wellhead area, helideck (built by Vindholmen Services in Arendal), crane, control room, workshop, test separator and glycol pump.
Normally unmanned, the platform is maintained as and when required and therefore incorporates a simplified accommodation module with lounge, mess, coffee room, galley, changing room, WC and 12 emergency beds.
Published 24. June 2017 • Updated 25. October 2019
Gulftide was converted to cope with conditions on Ekofisk in the Åmøy Fjord near Stavanger. This jack-up drilling rig was equipped with process equipment and its derrick, helideck, hangar and legs were reinforced.
To win time, it was decided that the discovery well and three appraisals drilled on Ekofisk by Ocean Viking would be completed for production.
Principles for producing from Gulftide were relatively simple. Output flowed from the subsea wellheads to the platform, where it went through two-stage separation to remove gas and water.
With pressure also reduced, the gas was flared off and the oil sent on by flowlines to two loading buoys where shuttle tankers moored to take on cargo.
Production could only continue while ships were loading. As soon as one tanker had been filled, the oil stream was diverted to the vessel waiting at the other loading buoy.
The problem with this approach was manifested when weather conditions – strong winds and/or high waves – forced the tankers to leave the buoys.
If that happened, production from the wellheads had to be suspended immediately. Given the prevailing weather on Ekofisk, that happened regularly. Output was halted for 20 per cent of the time during the first year.
Gulftide was replaced as the temporary production installation in 1974 by the permanent Ekofisk 2/4 A (Alpha) and 2/4 B (Bravo) platforms for production, drilling and quarters.
In addition came the Ekofisk 2/4 C (Charlie) production, drilling and compression facility, the Ekofisk 2/4 FTP (field terminal platform) for production and risers, and Ekofisk 2/4 Q for accommodation.
Oil and gas were produced by 2/4 A, B and C through their own wells for processing in their separation plants and piping on the 2/4 FTP for a three-stage separation process.
At the same time, the tanker loading buoys were moved further from the platforms and the Ekofisk 2/4 T oil storage tank became operational.
This facility was extremely advantageous, because it allowed production to continue virtually regardless of whether bad weather prevented tankers from connecting to the buoys.
The 2/4 FTP platform, where oil and gas from the three producing facilities was processed, had been planned to handle the level of output estimated for the main field.
Clear restrictions had been imposed by the Norwegian government on the amount of gas Phillips was allowed to flare. That also set a ceiling for oil production, since gas accompanies it up from the reservoir.
The solution was to install two powerful compression packages on 2/4 C in order to inject the gas under pressure back into the producing formation.
Accommodation facilities had to be provided on the two first platforms, 2/4 A and B. Where 2/4 C and FTP were concerned, however, they were tied together with bridges and to 2/4 Q.
Published 1. September 2019 • Updated 8. October 2019
A mere 17 months after the Ekofisk discovery was announced in December 1969, Gulftide was ready to come on stream as a temporary production platform.
Its official inauguration took place on 9 June, with initial test output commencing on 15 June. Full production began on 8 July.
The rig was chosen because it was available on the market. Established equipment for processing oil and gas was tailored to the limited space on board. Separate flowlines carried wellstreams from four subsea wells. Oil, gas and water were separated on board, with the gas flared and the oil piped to two buoys for loading into shuttle tankers.
Work on the process equipment was relatively simple. The problem was to tailor it to the rig. The subsea wellheads had to be reinforced to meet the demands posed by the North Sea, and a buoy loading system needed to be developed for waters where this technology had never been used before.
To gain time, it was decided that the three appraisal wells drilled by Ocean Viking to map the extent of the field – in addition to the discovery well – would be completed for production.
Første testflamme tent på Ekofisk. På Gulftide
1973, Teddy Broadhurst, gulftide,
Gulftide, separator – på bildet kan man se at det er fire brønner.
arbeidsliv, gulftide, pionerkultur, arbeid, dekk, Norges første havbunnsbrønner, historie, 1971,
The producers would be topped with hydraulically controlled wellheads. Such equipment had been tried out on the seabed earlier, but on a limited scale and not in the deep and rough waters found on Ekofisk. This challenge was overcome by having the wellheads manufactured and then reinforced at the Phillips base in Dusavik outside Stavanger. Flowlines and control cables would also be laid from each well to Gulftide, with production comingled in a single riser to the topsides.
Weather conditions also represented a major problem when designing the loading buoys. Phillips itself had experience with such facilities, but the concept had only been used before in harbour-like conditions and waters no deeper than 27 metres. They were now to stand in 70 metres in the middle of the North Sea.
Gulftide was converted in the Åmøy Fjord outside Stavanger to cope with conditions on Ekofisk. The processing facilities were installed and reinforcements made to the derrick, helideck, hangar and leg structures.
Planning began in late 1970, when Phillips received approval to begin laying the flowlines between wellheads and rig. Brown & Root won this contract, with the first oil pipelines on the Norwegian continental shelf laid by the Hugh W Gordon laybarge.
The production principle on Gulftide was relatively simple. Output flowed from the subsea wellheads to the rig, where it passed through two separation levels to be split into oil and gas while the huge pressure was reduced.
Gas was flared off and the oil was piped to one of the loading buoys where a shuttle tanker was moored. Production could only take place when a ship was present.
As soon as one tanker had become fully laden, the oil flow was switched to the other buoy where another ship was waiting to take on cargo.
The problem with this approach arose when weather conditions meant the tankers had to cast off from the buoys because of strong winds or high waves. The rig then had to shut down production from the wellheads immediately.
Given the weather conditions found on Ekofisk, output regularly had to cease. Production was suspended for 20 per cent of the first year for this reason.
Output began cautiously on 8 July 1971 from a single well. The second producer came on stream that September, the third was ready the following month and all four were producing by February 1972. They each flowed 10 000 barrels of oil per day.
Source: Kvendseth, Stig, Giant discovery, 1988.
Published 9. April 2019 • Updated 25. October 2019
The Greater Ekofisk Area lies at the southern end of Norway’s North Sea sector, roughly 280 kilometres south-west of Stavanger, and encompasses Ekofisk – the first Norwegian oil field – as well as Eldfisk and Embla.
— Sunset over Ekofisk. Photo: Husmo Foto/Norwegian Petroleum Museum
The three are operated by ConocoPhillips on behalf of the Ekofisk licensees. The area also embraces former producers Albuskjell, Cod, Edda, Tor, West Ekofisk and Tommeliten G.
These fields all lie within production licence 018 apart from Tommeliten G, which was operated by Statoil from 1976 to 2003.
In all, 31 installations have been positioned in the Greater Ekofisk Area.
First Norwegian offshore field
Ekofisk began production on 15 June 1971, following its discovery in the autumn of 1969. Development of the field has occurred in several phases.
Its central facilities were installed during the early 1970s, with oil initially being buoy-loaded into tankers. From 1975, it has been piped to Teesside in the UK. The gas has been landed by pipeline at Emden in Germany from 1977.
Jacked up six metres
The water depth in the Greater Ekofisk Area is 70-75 metres. However, declining pressure in the Ekofisk reservoir over the years has caused the seabed to subside.
Efforts began as early as 1985 to safeguard the installations against the effects of this development, and the steel platforms in the Ekofisk Complex were jacked up by six metres in 1987.
In addition, a protective breakwater was installed around the Ekofisk tank in 1989. The rate of seabed subsidence has declined sharply in recent years.
Waterflooding improves recovery
The Ekofisk 2/4 K water injection platform became operational in December 1987 as part of efforts to improve Ekofisk’s recovery factor – the share of petroleum in place actually produced.
Waterflooding capacity on the field to help maintain reservoir pressure was later expanded several times, and had reached just over 500 000 barrels per day by 2019.
Measured in barrels of oil equivalent, the recovery factor on Ekofisk has risen from an original estimate of 17 per cent to over 50 per cent.
Ekofisk I and II plus licence extension
The first phase of development and production on Ekofisk began with initial oil output from the converted Gulftide jack-up rig in 1971 and ended with the start-up of Ekofisk II in 1998.
Large parts of the Greater Ekofisk Area were restructured in the latter year, leading to plans for removing 15 installations – 14 steel platforms and the process facilities on the Ekofisk tank.
Designated Ekofisk I, these redundant structures include Ekofisk 2/4 A, 2/4 B, 2/4 FTP, 2/4 Q, 2/4 H, 2/4 R, 2/4 P and 2/4 T.
In addition come the Edda 2/7 C, Albuskjell 1/6 A, Albuskjell 2/4 F, Cod 7/11 A, West Ekofisk 2/4 D, Norpipe 36/22 A and Norpipe 37/4 A installations.
The concrete part of the tank – Ekofisk 2/4 T – will remain. Gulftide was removed as far back as 1974. Two platforms owned by other companies – Ekofisk 2/4 G and 2/4 S – have also gone.
A new plan for development and operation (PDO) of the field (Ekofisk II) was approved in 1994, at the same time as the Ekofisk licence was extended to 2028.
This creates a new Ekofisk Complex with two structures – the Ekofisk 2/4 X wellhead unit installed in the autumn of 1996 and the Ekofisk 2/4 J processing and transport platform in 1997.
Ekofisk II became operational in August 1998 and is intended to produce until 2028. Ekofisk, Eldfisk and Embla are tied back to the new complex, as was Tor until it shut down in December 2015.
In December 2002, soon after the Conoco-Phillips merger had been announced, the Ekofisk West project was presented to improve oil and gas recovery. Process capacity and reliability on Ekofisk were also to be enhanced.
This development primarily involved the construction and installation of a new platform, Ekofisk 2/4 M, with processing facilities and 24 new wells drilled over five years.
The latter could contribute to improved recovery both because there were more wells and because they would tap new locations in the reservoir. On stream in 2005, 2/4 M was linked to the Ekofisk Complex with a bridge.
Process capacity for produced water was also to be increased through upgrading on Ekofisk 2/4 J and Eldfisk 2/7 E. A third measure concerned laying a power cable from the Ekofisk Complex to 2/4 K in order to make electricity supplies more efficient.
New developments: Eldfisk II and Ekofisk South
The plan for development and operation (PDO) of Eldfisk II, approved by the Storting (parliament) on 9 June 2011, includes a new wellhead, process and accommodation platform – Eldfisk 2/7 S.
In addition come 42 new wells as well as upgrades to existing platforms which extend their commercial life.
The PDO for Ekofisk South involves the construction of a new wellhead platform – Ekofisk 2/4 Z – as well as a new subsea water injection facility and 44 additional wells.